UPVC Replacement Door Handles
The handles on your doors get worn out with time and require to be replaced. In this case, it is crucial that the new handles are in line with the critical dimensions of the old handle.
The top screw's position, the lever and the keyhole sizes are the three measurements you have to determine. Use the size guide to assistance in this.
Inline Lever/Lever
A lever/lever handle is a modern door handle designed to suit new or replacement doors. This style of door handle is available in a wide range of styles & finishes. A number of manufacturers offer this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The handles of uPVC/Composite are constructed from robust materials, and are ideal for multi-point lock doors that require a robust design. The handles are inline and operate off the same spindle and screw fixings so they are easily installed on doors made of uPVC/Composite, either new or old.
The handle can be adjusted and angled to suit all users. The handle has been endurance-tested to 200 000 cycles. This ensures that the finish is of high quality and performance is maintained over time. The lever that springs is adjustable to accommodate a wide range of locks. This is useful for doors with narrower openings where the cylinder is further away from the door. A lever that is shorter can be used for doors that have a latch that can be opened by the thumb inside.
Lever Pad
The lever pad upvc handle is distinct from the lever handles found on most doors. The handle can use a single spindle (inline) or independently from each side using two inline or offset spindles (pad). They are usually used on UPVC double-glazed doors and are available in a variety of variations and styles.
The handles are available in a variety of finishes, including White, Chrome, and Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This provides the handle with an outstanding performance and durability for the purpose it was designed for.
All UPVC levers for handles include a spindle and screws and can be mounted on the uPVC door. The backplate fixing centers of 211mm permit a bigger handle, which is often a benefit in replacing a defective or worn multi-point door lock mechanism. These levers for handles are also sprung, solving the problem of door handles sagging from their horizontal position when they are not being used.
When choosing the replacement UPVC handle and spindle it is essential to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement is also known as the 'handle centre' or 'cylinder centres' and is a critical aspect of matching up the right handles.
Once you have the proper PZ size, you'll be required to make sure that the handle lever pads and push pads are of a suitable shape to fit the American with Disabilities Act (ADA) compatible handles you require for your doors. These are typically round or square, with an internal lever, and an external push pad.
The majority of UPVC lever pads we offer are sprung, which means that they return to their horizontal position when they are not in use, instead of hanging out and potentially sticking in the frame. This stops draughts and cold air from getting into a house. Also, the majority of UPVC handle lever pad style handles are hand-operated which allows you to place them on either side of the door.
Euro Cylinder
Cylinder locks can be found on uPVC and other kinds of doors. They work by using a key that unlock a cylinder case that will reveal pins that can be aligned with those in the lock body and allow them to rotate a revolving cam, thus opening the door. Euro cylinders can be fitted with up to six pins with both internal and external doors usually needing different levels of security.
The choice of the correct cylinder is vitally important; this is dependent on how your doors and handles are utilized. For instance, exterior doors must be secured with an extra secure cylinder, while doors inside can be secured using a standard cylinder. Additionally, certain cylinders are available with extra features which can enhance security further, such as anti-drill and anti-bump characteristics.
To make sure that the euro cylinder is the right size for your door, it must be measured accurately. The cylinder should be measured from the hole for fixing screws in the middle to the other end of the cylinder and the thumb turn if you have one. If you are unable measure it using the lock in its position, you can take it out of it. It is crucial to not have a cylinder that extends beyond the handle or escutcheon. This could make it susceptible to lock snapping attacks.
door handle replacement are constructed with bump and anti-drill features included in their design. These are designed to reduce the chances of an attack by forcing the cylinder to rotate in a different direction. This will help to stop the attack and ensure your doors are secure.
There are also cylinders that have been made to resist snapping. This is a common attack on cylinders. A special tool is used to break the break line of the lock, and then the front of the cylinder is snapped off. This is faster and less difficult than opening multipoint locks. It also leaves little evidence of a break-in, which could hinder an insurance claim.
Spring Cassette
The spring cassette is positioned in the base of your door handle backplate providing a sprung solution to return your multipoint lock handles to their original position after using. Previously a lot of handles did not have a spring integrated into them, and as a result, they are more likely to slide or drop when the locking mechanism has been disengaged. This simple feature is among the most effective ways to fix this and it is also a great way to prevent your doors made of upvc from becoming stuck in the open or closed position, as these aren't always simple to manually close by hand.
The spring cassettes were made to be used with a spring multipoint locks. They are not compatible with handles that aren't sprung and you'll need to cut a hole into the backplate to allow them to fit. (Please see the image for a detailed diagram). They are a replacement for existing damaged or missing cassettes inside the door handle backplate of numerous brands of uPVC doors. They are sold as one unit. They have a square-cut out that accommodates an 8mm shaft.
These spring cassettes are a fantastic value for money way to fix the problem of your door handles that are sagging. They are simple to put in and will extend the life span of your uPVC doors. Contact us for more information about our wide range of uPVC accessories and spares. We are always available to offer professional advice and assistance you.